| |
RM1-6181-000CN
Fusing Assembly - For 220 VAC - Bonds toner to paper with heat
|
Q2425-69009
Fuser assembly for LJ 4200 series - 110 volt Bonds toner to paper with heat - For 100 to 127VAC operation
|
RA1-7708-040CN
Delivery roller - Has four 'Foam' rollers - For (Face down) top of printer paper output
|
H3978-60002
Maintenance Kit (220V) - Includes fuser roller assembly, transfer roller assembly, Tray 1 and Tray 2 pickup rollers, Tray 1 and Tray 2 separation pads - Procedure requires use of service manual - Not for warranty use
|
C9656-69019
Fuser Assembly - 220 volts Fuser Assembly - Bonds the toner to the paper with heat - For 220VAC to 240VAC operation
|
RU5-8934-000CN
fUSER UNIT / FIXING PAPER DELIVERY Assy (110V)FUSER UNIT FOR PRO SERIES M SERIES P MODELS.
|
CH955-67123
Carriage shutdown service kit - Includes carriage bushings carriage felts cleaning sponge lubricant oil (10ml) gloves bushing replacement procedure and carriage rail maintenance procedure for end user
|
B5L24-67904
Paper pick-up roller assembly - Part of tray 2 to 5 roller kit Tray 2-5 Pickup / Separation Assembly Kit
|
C4155A
Fusing assembly kit - 120V - Includes the fusing assembly, six paper pickup/feed rollers, and toner cloth
|
C8563A
Magenta imaging drum assembly - Includes the photosensitive drum (or OPC), developing cylinder, and a small amount of toner (for priming) - Life expectancy is approximately 40,000 pages
|
|
|
C2003-69001
Fusing assembly (120V, 60Hz) - Bonds toner to paper by heat
|
RF5-1534-000CN
Transfer roller - Located underneath toner (EP) cartridge
|
|
|
|
|
RG5-6283-000CN
Pickup roller assembly - Includes a steel shaft with a rubber D shaped roller, drive gear, bushings, sesnor flag, and two retaining clips - Mounts in the bottom of the ADF paper pickup assembly
|
|
|
RM2-5679-000CN
Fusing assembly - For 110-127 VAC operation - Bonds toner to the paper with heat
|
RM2-5178-000CN
Fusing assembly - For 220 VAC - Bonds toner to the paper with heat
|
RM1-3007-000CN
Fuser Assembly - For 110 VAC - Bonds toner to paper with heat
|
RG5-1964-020CN
Heating element assembly (For 100VAC to 120VAC operation) - Hollow shaft with heating element inside - Yellow `Warning hot` label on top - Plastic sleeve not available separately
|
RM1-1043-000CN
Fusing Assembly - For 100-127 VAC - Bonds toner to paper with heat
|
C4118-69001
Maintenance kit (120V) - Includes exchange 120VAC fusing assembly, transfer roller, six pickup/separation rollers, MP Tray/Tray 1 pickup roller, vinyl gloves, and instruction guide
|
Q5669-67008
Preventive maintenance kit - Includes the complete service station and left spittoon - For the 24/44-inch DesignJet Z Model photo printer series
|
F1660-69103
64MB 100MHz CL2 3.3v 144-pin SDRAM SO-DIMM memory module
|
CB506-67903
Transfer roller assembly - Long black foam type roller - Transfers static charge to paper
|
RG5-7451-130CN
LaserJet 4650 fusing assembly - For 220 VAC operation - Bonds toner to paper with heat
|
RM1-2743-180CN
Fuser Assembly - For 220 VAC to 240 VAC operation - Bonds toner to paper with heat
|
RL1-0303-000CN
Paper pickup roller (D-shaped roller) - Picks up media from the paper input tray
|
C2684-60219
Drive roller assembly - Has 4 large rollers
|
|
|
RG5-4119-000CN
Delivery roller assembly - Lower face-down output roller assembly - Includes roller and holder Four used
|
CE502-67909
Fusing Assembly - For 110 VAC operation - Bonds toner to paper with heat
|
RM1-8808-020CN
Fuser assembly - For 110 VAC - Bonds toner to paper with heat
|
|
|
|