| |
RF5-1077-030CN
Lower delivery roller - Shaft with 4 double rollers on it
|
RC1-3994-000CN
Face down roller - Small individual feed roller that rides against face down shaft roller - Held by torsion spring - Four used
|
RM1-0370-000CN
Face down top output bin delivery roller assembly - Includes roller and holder
|
|
|
RG5-5560-070CN
Fusing roller - (For 110V to 120V operation) - Includes heating element and fixing sleeve only
|
RM1-0103-060CN
Fixing film assembly - Includes heating element, heating element housing tube and fuser film sleeve - 110 volt
|
|
|
|
|
RG9-1542-000CN
Transfer roller assembly - Transfers static charge to the media being printed on
|
|
|
RG5-3644-030CN
Pickup roller assembly - Includes the roller shaft with the paper pickup (D-shaped) roller, two hard plastic side cams, and bushings - Mounts in the top front of the 250-sheet paper feeder assembly base unit
|
RG5-4283-000CN
Transfer roller assembly - Long metal shaft with Black roller and drive gear - Transfers static charge to the media being printed on
|
|
|
RF5-0596-000CN
Transfer charge roller (Black) - Behind transfer guide assembly
|
RC1-3909-000CN
Pickup roller assembly - Rubber roller on a short shaft with slots on the end - Does NOT include the two flanking hard plastic rollers
|
RM2-5752-000CN
Kit-Trays 2X Roller sets RM2-5752-000CN Tray x2 Separation Roller and x2 pickup roller Assembly for HP M501 M506 M527 M426 M402
|
RC1-5440-000CN
Paper pickup roller (D-shaped roller) - Picks up media from the paper input tray - Clips in the holder on the paper pickup shaft in the paper feeder assembly
|
Q7829-67924
Pickup roller high capacity input (HCI) - Attached to the pickup arm - Presses down the paper stack surface to feed the paper one sheet at a time (white)
|
RG5-6281-000CN
Feed roller assembly - Includes a steel shaft with five rubber rollers, two bushings, a spring, and E clips - Mounts to the left of the paper pickup roller in the bottom of the ADF paper pickup assembly
|
RG5-1965-020CN
Heating element assembly (For 220V to 240V operation) - Hollow shaft with heating element inside - Plastic sleeve not available separately
|
|
|
|
|
|
|
RB3-1034-000CN
Pressure roller assembly - Hard rubber roller on a metal drive shaft
|
RB2-6369-000CN
Pressure roller - Applies pressure to paper as it feeds through the fusing roller
|
|
|
RG5-0161-090CN
Registration assembly - Next set of rollers after paper pickup
|
E6B67-67905
Paper feed roller assembly - Part of tray 2-6 roller kit
|
|
|
FF5-5207-000CN
Separation roller - Shaft and three center rollers attached to the roller shaft in ADF separation roller assembly
|
RG5-6897-020CN
Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two anti-reversing flaps, and the drive gear
|
|
|
RB3-0129-020CN
Feed roller assembly - Includes the metal shaft and two small rubber rollers - Feeds paper from the paper cassette (or tray three below) into the printer - Mounts on the top of the center frame in the base on the 250-sheet input tray assembly
|
RM1-0550-000CN
Transfer roller assembly - Transfers static charge to the media being printed on
|
RA2-2118-000CN
Paper drive roller (Shaft with four rubber rollers on it) - Mounts in the rear of the switchback area of the duplexer (Rollers extend through cut outs in the rear support frame)
|
|