|
| |
C4557-40063 is represented by #1 in the diagram below.
- 1
- 1 C4557-40063 - Separator lifter - Used to lift the separator peg
- 2
- 2 C4557-20024 - Shifter spring - Provides tension on the pivot
- 4
- 4 C4557-40095 - Encoder gear for HP Color Copier 260
- 4 C4557-60025 - Pivot feed roller - Shaft with 4 hard rollers - Does not include other items such as gear or encoder
- 4 C6409-60037 - Pivot feed roller assembly - Shaft with small rollers and paper encoder - This item should be replaced only by trained, experienced service personnel
- 4 C6455-60057 - Shift plate assembly - Five plastic gears held in a two piece plastic frame - Attaches to feedroller assembly
- 5
- 5 C4557-40150 - Pivot snap - Used to hold pivot to pick feed roller shaft
- 6
- 6 C5870-00004 - Wear strip - Long, spring loaded strip mounted in top of backbone - Used to ensure smooth ink cartridge carriage motion
- 7
- 7 C4557-20028 - EOR tension spring - Maintains tension on wear strip
- 8
- 8 C6409-00013 - BacKBone - Large metal item where the main logic PCA and the carriage drive motor are mounted - This item should be replaced only by trained, experienced service personnel
- 10
- 10 C5870-40020 - Right backbone brace - Installed on right side of printer base to provide support for backbone
- 12
- 12 C4557-00033 - Link spring - Provides tension to shaft of pick cam gear
- 13
- 13 C6409-40040 - Pick cam - Controls pressure plate and lever
- 16
- 16 C4557-00037 - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker
- 18
- 18 C4557-40016 - Kicker - Restacks paper in stack after top sheet is picked
- 19
- 19 C4557-40020 - Lower guide - Platform for seperator peg, spring and pad
- 20
- 20 C4557-20003 - Rear roller spring - Flexible axle for rear roller
- 20
- 20 C4557-20003 - Rear roller spring - Flexible axle for rear roller
- 21
- 21 C5870-40022 - Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment
- 21
- 21 C5870-40022 - Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment
- 22
- 22 C4557-00035 - Paper pusher spring - Maintains alignment in paper tray
- 22
- 22 C4557-00035 - Paper pusher spring - Maintains alignment in paper tray
- 23
- 23 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 24
- 24 C4557-00009 - Separator spring - Provides pressure between separator assembly and the center drive roller
- 26
- 26 C4557-60011 - Separator pad for HP DeskJet 700 Series
- 28
- 28 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 28
- 28 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 28
- 28 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 28
- 28 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 29
- 29 C6409-00008 - Upper paper guide support - Base for upper paper guide
- 30
- 30 C4557-40130 - Left wall brace - Provides support for left wall
- 31
- 31 C4557-40128 - Left backbone brace - Provides support for backbone
- 34
- 34 C5870-40030 - Pivot assembly - Large plastic Item below the feed roller assembly - Picks and feeds media through print mechanism - Should be replaced only by experienced service personnel
1
C4557-40063
Lifter
Separator lifter - Used to lift the separator peg
2
C4557-20024
Spring
Shifter spring - Provides tension on the pivot
4
C4557-60025
Roller
Pivot feed roller - Shaft with 4 hard rollers - Does not include other items such as gear or encoder
4
C6409-60037
Roller
Pivot feed roller assembly - Shaft with small rollers and paper encoder - This item should be replaced only by trained, experienced service personnel
4
C6455-60057
Plate
Shift plate assembly - Five plastic gears held in a two piece plastic frame - Attaches to feedroller assembly
5
C4557-40150
Snap
Pivot snap - Used to hold pivot to pick feed roller shaft
6
C5870-00004
Strip
Wear strip - Long, spring loaded strip mounted in top of backbone - Used to ensure smooth ink cartridge carriage motion
7
C4557-20028
Spring
EOR tension spring - Maintains tension on wear strip
8
C6409-00013
Backbone
BacKBone - Large metal item where the main logic PCA and the carriage drive motor are mounted - This item should be replaced only by trained, experienced service personnel
10
C5870-40020
Brace
Right backbone brace - Installed on right side of printer base to provide support for backbone
12
C4557-00033
Spring
Link spring - Provides tension to shaft of pick cam gear
16
C4557-00037
Lever
Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker
18
C4557-40016
Paper Stacker
Kicker - Restacks paper in stack after top sheet is picked
19
C4557-40020
Guide
Lower guide - Platform for seperator peg, spring and pad
20
C4557-20003
Spring
Rear roller spring - Flexible axle for rear roller
21
C5870-40022
Lever
Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment
22
C4557-00035
Spring
Paper pusher spring - Maintains alignment in paper tray
23
C4557-40118
Foot
Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
24
C4557-00009
Spring
Separator spring - Provides pressure between separator assembly and the center drive roller
28
C4557-20007
Spring
Pinch spring - Provides tension on upper paper guide
29
C6409-00008
Support
Upper paper guide support - Base for upper paper guide
30
C4557-40130
Brace
Left wall brace - Provides support for left wall
31
C4557-40128
Brace
Left backbone brace - Provides support for backbone
34
C5870-40030
Roller
Pivot assembly - Large plastic Item below the feed roller assembly - Picks and feeds media through print mechanism - Should be replaced only by experienced service personnel
|
|