|
| |
C2162-67813 is represented by #19 in the diagram below.
- 1
- 1 C2145-00017 - Lever arm spring - Provides tension between the lever arm and the pressure plate lifter
- 2
- 2 C2164-67812 - Pivot assembly (Quiet kick) - Large plastic item with large rollers - Picks and feeds media through print mechanism - Has a clear plastic piece immediately to right of gear
- 2 C4549-67806 - Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism
- 3
- 3 C4562-40032 - Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt
- 4
- 4 C4549-60036 - Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers
- 6
- 6 C4562-40022 - Rotation limiter - Provides correct pressure to cap pen
- 7
- 7 C2162-40036 - Flex Support - Supports Flex Circuitry of Carriage Assembly
- 9
- 9 C6450-80052 - Spittoon sponge - located in bottom of spittoon
- 10
- 10 C6450-40011 - Spittoon - Holds ink expelled from cartridge during refresh cycle
- 11
- 11 C2124-00009 - Spring - Installed in spittoon assembly
- 12
- 12 C2162-20004 - Pivot spring - Provides tension for pivot to return to upright position
- 13
- 13 C2162-67806 - Preloader - Applies downward pressure on drive shaft
- 14
- 14 C2164-40060 - Carriage belt for HP DeskJet 550C Series
- 15
- 15 C2162-40105 - Switch lever - Actuates access door (Open) switch
- 16
- 16 C2162-40002 - Cluster gear for HP DeskJet 500 Series
- 18
- 18 C2162-40016 - Idler hub - Drive belt pivot point on left side of chassis
- 20
- 20 C2162-20005 - Carriage rod - Supports horizontal carriage movement
- 21
- 21 C4562-20003 - Idler pulley axel - Dowel pin for idler pulley
- 22
- 22 C2124-20001 - Rear rail - Supports carriage assembly
- 23
- 23 C2124-00001 - Encoder spring - Provides tension for encoder strip
- 25
- 25 C2162-60009 - Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
- 25
- 25 C2162-60009 - Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
- 26
- 26 C2164-67809 - Ink cartridge carriage assembly - Includes trailing cable
- 27
- 27 C2164-67811 - Service station assembly with motor - Mechanical assembly that moves the service station sled
- 28
- 28 C6450-60102 - Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges
- 29
- 29 C2124-80008 - Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position
- 31
- 31 C2164-60045 - Paper stepper motor assembly (does NOT include cable)
- 32
- 32 C2124-60190 - Service station stepper motor (does not include cable) - Moves the rack vertically in the service station assembly
- 33
- 33 C2162-60006 - Carriage motor assembly (includes cable)
- 34
- 34 C4549-60035 - Paper width adjustment stop - Adjusts for input paper width
1
C2145-00017
Spring
Lever arm spring - Provides tension between the lever arm and the pressure plate lifter
2
C2164-67812
Roller
Pivot assembly (Quiet kick) - Large plastic item with large rollers - Picks and feeds media through print mechanism - Has a clear plastic piece immediately to right of gear
2
C4549-67806
Roller
Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism
3
C4562-40032
Bracket
Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt
4
C4549-60036
Plate
Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers
6
C4562-40022
Limiter
Rotation limiter - Provides correct pressure to cap pen
7
C2162-40036
Support
Flex Support - Supports Flex Circuitry of Carriage Assembly
9
C6450-80052
Absorber
Spittoon sponge - located in bottom of spittoon
10
C6450-40011
Spitton
Spittoon - Holds ink expelled from cartridge during refresh cycle
12
C2162-20004
Spring
Pivot spring - Provides tension for pivot to return to upright position
13
C2162-67806
Spring
Preloader - Applies downward pressure on drive shaft
15
C2162-40105
Lever
Switch lever - Actuates access door (Open) switch
18
C2162-40016
Hub
Idler hub - Drive belt pivot point on left side of chassis
20
C2162-20005
Rod
Carriage rod - Supports horizontal carriage movement
21
C4562-20003
Pin
Idler pulley axel - Dowel pin for idler pulley
23
C2124-00001
Spring
Encoder spring - Provides tension for encoder strip
25
C2162-60009
Cable
Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
26
C2164-67809
Carriage
Ink cartridge carriage assembly - Includes trailing cable
27
C2164-67811
Service Station
Service station assembly with motor - Mechanical assembly that moves the service station sled
28
C6450-60102
Sled
Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges
29
C2124-80008
Strip
Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position
31
C2164-60045
Motor
Paper stepper motor assembly (does NOT include cable)
32
C2124-60190
Motor
Service station stepper motor (does not include cable) - Moves the rack vertically in the service station assembly
34
C4549-60035
Stop
Paper width adjustment stop - Adjusts for input paper width
|
|