|
| |
C2162-40016 is represented by #44 in the diagram below.
- 1
- 1 C4549-40028 - Lever arm - Used to lift the pressure plate lifter
- 2
- 2 C2128-40055 - PPS adjuster - Used to adjust the distance between the pivot and the pen
- 4
- 4 C2128-40019 - Separator Peg - Lifts the separator pad when the lifter shaft lifts
- 8
- 8 C2162-60006 - Carriage motor assembly (includes cable)
- 9
- 9 C2145-00017 - Lever arm spring - Provides tension between the lever arm and the pressure plate lifter
- 10
- 10 C4562-60065 - Chassis assembly - The large plastic item that forms the base of the print mechanism
- 11
- 11 C4549-40006 - Lifter shaft - Plate like shaft that lifts the pressure plate
- 12
- 12 C2128-00006 - Separator spring - Provides pressure between the separator assembly and the center drive roller
- 13
- 13 C2170-00008 - Right bracket - Carriage rod adjustment bracket (Right)
- 14
- 14 C2128-40032 - Center lifter cap - Holds the pressure plate lifter and the kicker spring in place
- 15
- 15 C2128-00002 - Kicker spring - Provides tension for the kicker
- 16
- 16 C2128-40015 - Left lifter cap - Holds the pressure plate lifter in place
- 17
- 17 C2162-60009 - Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
- 18
- 18 C2124-20008 - Limiter spring - Provides tension for rotation limiter
- 19
- 19 C4562-40022 - Rotation limiter - Provides correct pressure to cap pen
- 21
- 21 C2162-40105 - Switch lever - Actuates access door (Open) switch
- 22
- 22 C4549-40017 - Right wall stop - Maintains alignment of small media sizes in the input tray
- 22 C4549-60036 - Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers
- 23
- 23 C4549-67806 - Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism
- 24
- 24 C2162-67802 - Paper width adjustment stop - Adjusts for input paper width
- 25
- 25 C4549-40027 - Clutch actuator - Pulls the clutch against the drive gear which starts the media picking process
- 26
- 26 C6450-40011 - Spittoon - Holds ink expelled from cartridge during refresh cycle
- 27
- 27 C2162-40002 - Cluster gear for HP DeskJet 500 Series
- 28
- 28 C2162-20004 - Pivot spring - Provides tension for pivot to return to upright position
- 30
- 30 C2124-00009 - Spring - Installed in spittoon assembly
- 31
- 31 C2162-60009 - Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
- 32
- 32 C2162-67806 - Preloader - Applies downward pressure on drive shaft
- 33
- 33 C6450-60102 - Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges
- 34
- 34 C6450-80052 - Spittoon sponge - located in bottom of spittoon
- 35
- 35 C2124-20004 - Belt spring - For belt tension bracket
- 36
- 36 C2162-40036 - Flex Support - Supports Flex Circuitry of Carriage Assembly
- 37
- 37 C2164-60045 - Paper stepper motor assembly (does NOT include cable)
- 38
- 38 C2124-80008 - Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position
- 39
- 39 C2165-00001 - Left bracket - Carriage rod adjustment bracket (Left)
- 41
- 41 C4562-40032 - Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt
- 42
- 42 C2124-00001 - Encoder spring - Provides tension for encoder strip
- 44
- 44 C2162-40016 - Idler hub - Drive belt pivot point on left side of chassis
- 46
- 46 C2162-20005 - Carriage rod - Supports horizontal carriage movement
- 47
- 47 C2128-40020 - Kicker - Straightens the stack of media in the input tray so that the separator can function consistently
- 48
- 48 C2164-40060 - Carriage belt for HP DeskJet 550C Series
1
C4549-40028
Arm
Lever arm - Used to lift the pressure plate lifter
2
C2128-40055
Adjuster
PPS adjuster - Used to adjust the distance between the pivot and the pen
4
C2128-40019
Peg
Separator Peg - Lifts the separator pad when the lifter shaft lifts
8
C2162-60006
Motor
Carriage motor assembly (includes cable)
9
C2145-00017
Spring
Lever arm spring - Provides tension between the lever arm and the pressure plate lifter
10
C4562-60065
Chassis
Chassis assembly - The large plastic item that forms the base of the print mechanism
11
C4549-40006
Lifter
Lifter shaft - Plate like shaft that lifts the pressure plate
12
C2128-00006
Spring
Separator spring - Provides pressure between the separator assembly and the center drive roller
13
C2170-00008
Bracket
Right bracket - Carriage rod adjustment bracket (Right)
14
C2128-40032
Cap
Center lifter cap - Holds the pressure plate lifter and the kicker spring in place
15
C2128-00002
Spring
Kicker spring - Provides tension for the kicker
16
C2128-40015
Cap
Left lifter cap - Holds the pressure plate lifter in place
17
C2162-60009
Cable
Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
18
C2124-20008
Spring
Limiter spring - Provides tension for rotation limiter
19
C4562-40022
Limiter
Rotation limiter - Provides correct pressure to cap pen
21
C2162-40105
Lever
Switch lever - Actuates access door (Open) switch
22
C4549-40017
Stop
Right wall stop - Maintains alignment of small media sizes in the input tray
22
C4549-60036
Plate
Pressure Plate Assembly - Holds media to be printed against the Paper Input Feed Rollers
23
C4549-67806
Roller
Pivot assembly - Large plastic item with large rollers - Picks and feeds media through print mechanism
24
C2162-67802
Stop
Paper width adjustment stop - Adjusts for input paper width
25
C4549-40027
Actuator
Clutch actuator - Pulls the clutch against the drive gear which starts the media picking process
26
C6450-40011
Spitton
Spittoon - Holds ink expelled from cartridge during refresh cycle
28
C2162-20004
Spring
Pivot spring - Provides tension for pivot to return to upright position
31
C2162-60009
Cable
Cable assembly - Has 5-pin (F) connector on each end - 26.5cm (10.4in) long
32
C2162-67806
Spring
Preloader - Applies downward pressure on drive shaft
33
C6450-60102
Sled
Service station sled assembly - Mounts on top of the service station - Performs capping and wiping functions for the print cartridges
34
C6450-80052
Absorber
Spittoon sponge - located in bottom of spittoon
36
C2162-40036
Support
Flex Support - Supports Flex Circuitry of Carriage Assembly
37
C2164-60045
Motor
Paper stepper motor assembly (does NOT include cable)
38
C2124-80008
Strip
Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position
39
C2165-00001
Bracket
Left bracket - Carriage rod adjustment bracket (Left)
41
C4562-40032
Bracket
Belt tension bracket - Pivot bracket for idler pulley - Applies tension to the carriage belt
42
C2124-00001
Spring
Encoder spring - Provides tension for encoder strip
44
C2162-40016
Hub
Idler hub - Drive belt pivot point on left side of chassis
46
C2162-20005
Rod
Carriage rod - Supports horizontal carriage movement
47
C2128-40020
Kicker
Kicker - Straightens the stack of media in the input tray so that the separator can function consistently
|
|